frigidaire refrigerator online manuals

Try adjusting the humidity control for more air flow The display will show “Sb” while in Sabbath mode. Repeat the steps above to deactivate. Some things to keep in mind when your refrigerator is in Sabbath mode: The ice cube compartment will remain cold. For example, if you inadvertently left the refrigerator door open for a period of time, the HIGH TEMP alarm will signal for safety reasons.Also, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the ice bin to fill completely. The ice bin will hold about 4 pounds of ice. Set the freezer control to a colder setting to improve ice production. Allow 24 hours for the temperature to stabilize. Sometimes an ice cube or other object may be preventing the signal arm from freely moving. Additionally, ensure the ice bin itself is pushed all the way to the rear of the shelf. If this comes slightly out of place, it may prevent the signal arm from dropping all the way down and producing ice as it should. Feel free to discard the ice and allow a fresh supply to be produced. TIP: Ice production should be used at least twice a week to keep the cubes separated. This usually is due to the water filter being clogged or a restricted water supply. It is recommended to change the water filter first but if the condition still occurs then you want to check for a saddle valve, water valve not turned on all the way or kinked water supply line. Remember, smaller ice cubes or ice chips jamming in the ice maker may be a sign that your water filter needs changing. As the water filter becomes older (6 months or more) it can become clogged with particles and less water is delivered to the ice maker. The ice maker can’t fill every cube in the ice maker mold, leading to small cubes or ice chips that can get caught between the ice ejector blades and the stripper.

• frigidaire refrigerator manual online, frigidaire refrigerator online manuals, frigidaire refrigerator online manuals download, frigidaire refrigerator online manuals free, frigidaire refrigerator online manuals pdf, frigidaire refrigerator online manuals online, older frigidaire refrigerator manuals online, frigidaire refrigerator manuals online.

We appreciate your patience. For Side-by-Side, French-Door and Multi-Door refrigerators, the model and serial number can be seen along the upper right side of the fresh food compartment and is visible when the door is opened. You will also have easy access to your warranty information and product care tips. To register your product, you will need your Model and Serial number and date of purchase as shown on your receipt. You can register on-line. You can also drop your product registration card in the mail. If you have any questions, please contact us. Plus, you get all of the features and quality you expect. For more information, see: www.energystar.gov The label will tell you about the product's efficiency level, including approximately how much energy the appliance uses, its average annual operating cost, and how its energy use compares with that of similar products. For more information, see: However, most of your refrigerator can simply be cleaned using soap, water and a soft cloth. Be sure to wring excess water out of the sponge or cloth before cleaning around controls, light bulb or any electrical part. It provides streak-free shine, protective coating repels dust and dirt, and gently cleans tough stains. Wipe with the grain to prevent scratching. Always follow the manufacturer’s instructions when using. Is this normal? It is normal for the compressor to go on and off frequently. The thermostat keeps the refrigerator at a constant temperature. Single speed compressors (most Top-Freezer and Side-by-Side refrigerator models) Allow 24 hours for the temperature to stabilize. At times it may even run faster, such as after a defrost cycle. It is preferred that you do not adjust the temperature from the recommended setting during the 1st 24 hours. If you have any questions, please contact us. Here are some helpful tips: This keeps incoming air to a minimum and maintains maximum moisture.

Remember to order the same filter that is currently in your refrigerator. If you have any questions, please contact us. It is always recommended to check out your Owner’s Manual for more descriptions of these features and when best to use. Press selection directly on display for a few seconds until you hear an audible tone. If deactivating a selection, the LED light will no longer illuminate. If you have any questions, please contact us. The drawer automatically defaults to a locked state to prevent any unwanted use. To change the drawer’s settings, simply press Unlock and hold for 3 seconds. To change the drawer temperature when in the freezer temp setting, use the control panel display on the front door of your Multi-Door refrigerator. It’s important to note, when changing the temperature on the display, you will be changing both the drawer temperature setting AND the freezer compartment.Auto CrispSeal TM Drawers may be equipped with an automatic humidity control membrane. We do not recommend replacing the auto-humidity membrane unless it becomes damaged or dirty. If the membrane requires cleaning, it can simply be washed with soap and water. Make sure you thoroughly dry the membrane before replacing in your refrigerator. For further instructions regarding how to remove the auto-humidity membrane, check out your Owner’s Manual. If you have any questions, please contact us. To adjust your shelves: Lower the shelf into the desired slot and lock into position The shelves slide out independently of their mounting brackets. Just pull the front of the shelf forward. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. To change the position of an adjustable door bin simply: If you have any questions, please contact us.It is always recommended to check out your Owner’s Manual for more descriptions of these features. Use the UP or DOWN key to scroll through the menu that appears in the center of your display.

If you have any questions, please contact us. Air in new plumbing lines can result in an uneven water flow. To reset the shutoff device, simply release the dispenser paddle and then resume if needed. This is perfectly normal. Press and hold the lock key on your display for 3 seconds to unlock. The dispenser has a built-in device that shuts off after 3 minutes of continuous use to prevent the motor from overheating. To reset the shutoff device, simply release the dispenser paddle and then resume if needed. Remove the ice bin, thaw and empty contents. When new ice is produced, dispenser should operate. Take out the ice bin completely and remove the ice cubes. Replace the bin and the dispenser should operate. If the auger is accidentally rotated, you must realign the auger by turning it in 45 degree turns until the ice bin fits into place.Press and hold the lock key on your display for 3 seconds to unlock. The water filter may be clogged or overdue for replacement.However, air can be trapped in the new plumbing lines which can result in 2 or 3 empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. It will also prohibit the water to evenly flow initially from the dispenser. It may take about 1-2 minutes. Most Owner’s Manuals will provide you the water filter information specific to your model.On most models, the Water Filter Status on your display will illuminate and prompt you when it’s time to replace the filter. If your refrigerator has not been used for a period of time (during moving for example), it is recommended to change the filter before reinstalling the refrigerator. Remember to order the same filter type that is currently in your refrigerator. If you need more help, please contact us. Replacing the air filter will ensure optimal filtering of refrigerator odors. You may want to adjust this time period depending on the types and amounts of food you typically store in your refrigerator.

You will also need to provide the date of purchase as shown on your receipt. It’s always a good idea to save this information. If you have any questions, please contact Frigidaire at 1-800-374-4432. They’re perfect for storing laundry supplies, extra towels, cleaning supplies and more. They can also ensure your washer is at the optimal height for loading and unloading. Or you can check your model here or find it in your Installation Guide, which is also available online. To earn the Energy Star rating, products must meet strict energy efficiency criteria set by the U.S. Environmental Protection Agency or the U.S. Department of Energy. These products can help save money on your electricity bill and protect the environment by reducing harmful emissions from power plants, as well as providing all the features and quality you expect. This label signifies that the product passed stringent standards set by the U.S. Department of Energy. Additionally, manufacturers are required to display their product’s test results on the Energy Star label. The label will tell you about the product’s efficiency level, including approximately how much energy the appliance uses, its average annual operating cost and how its energy use compares with that of similar products. Your Complete Owner’s Guide will give you more information on those applicable to your model. You can also wash the lint screen in warm, soapy water to remove any residue, and then dry it thoroughly before replacing. Push or turn the start button and hold it for two seconds. To be sure it’s correctly positioned, simply turn the knob until the indicator is a little further into the cycle. The door must be completely closed for the dryer to run. Check to be sure the plug fits tightly into the wall outlet. Note: Do not use an extension cord. If this is the case, reset the circuit breaker or replace the fuse (but do not increase the fuse capacity).

When selection is made, go back and press OPTIONS to save. To adjust your shelves: Lower the shelf into the desired slot and lock into position The shelves slide out independently of their mounting brackets. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. To change the position of an adjustable door bin simply: If not aligned on either side, push the basket sideways until it is aligned. It is always recommended to check out your Owner’s Manual for more descriptions of these features. When selection is made, go back and press OPTIONS to save. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. Door reversal instructions can be found in your Installation guide. You may hear the sides lock into the tabs. No worries, just discard the ice made during the 1st 24 hours and then you should be good to go. NOTE: If the ice maker is ON and the water supply is not connected, the water valve will make loud chattering noises. Adjusting refrigerator control changes temperatures in both the refrigerator and the freezer. Adjusting the refrigerator control changes temperatures in both the refrigerator and the freezer. To maintain temperatures, a fan circulates air in the refrigerator and freezer and therefore, it is important not to block air vents with food items. This could disrupt the air flow and cause temperature issues. For some models: Adjusting the refrigerator temperature control “0” turns off the compressor and prevents the refrigerator from cooling but does not disconnect the power to the light and electronics. To completely turn off your refrigerator, you must unplug it. We appreciate your patience. The large capacity and fast dry times of our newer models save on energy use and time. Once you have registered, you will receive useful information including easy access to your warranty and product care tips.

If letting the motor cool down and reducing the load size does not resolve the issue, contact your authorized service provider. On electric dryers, a thermal limiter switch automatically turns off the motor in the unlikely event of an overheated situation. If this is the case, you’ll need to contact a service provider to replace the thermal limiter switch. How can I prevent this? Try using the Auto Dry cycle instead of a Timed Dry cycle, and follow care instructions on the fabric labels. For best results, follow these suggestions. We appreciate your patience. App store is a service mark of Apple Inc. Google Play is a trademark of Google Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Serial numbers beginning with KK0, KN0 or XK0 should use the 2.0 app. All others should use the original Frigidaire Smart Appliance app. The Frigidaire - Smart Appliances app is for older appliances and will be kept active until we migrate those existing customers to the new Frigidaire 2.0 app in late 2020. Once migration is complete, users will be notified to download the latest version of the app. Standard text rates may apply if you opt to receive text message notifications. App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. You will be prompted to enter your email address and you will be sent a link to reset your password. NOTE: Your account through the Frigidaire app is different from an account created on www.Frigidaire.com. The good news is that as soon as power is restored, the appliance will should automatically re-connect and function normally without user intervention. You may receive a “connection lost” notification in the Frigidaire app. You will use the same email address and password that you used during the initial set up.

Before doing so, the smart appliance will need to be removed from the Frigidaire app and taken through a Factory reset to clear the memory. To conduct the Factory reset, follow the steps listed below: You can then create a new account using a valid email address and password of at least 6 characters and one number (no spaces). Once you have accessed the Frigidaire app, press “Add My First Appliance” so you can be led through the connection steps. App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. What can I do? If it’s not, you will need to add a password Some dual-band or mesh networks may need to be manually switched to a 2.4 GHz network. Please contact your network provider if you are unsure of your network type. However, you will need to use the same email and password to login. What can I do to fix this? The schedule can be controlled from the Frigidaire app, and the appliance will keep the last known schedule in its memory until the schedule is turned off. The previous schedule will remain in the appliance’s memory until a new schedule is set. If this is not done, the appliance will continue to run on the last programmed schedule. What should I do? This is normal and you should be able to move forward. If the phone does not stay connected to the network, try checking your network settings for features like “Smart Network Switch”, “switch to mobile data” or “avoid weak networks”. If these features are active, they may impede the connection and should be temporarily turned off. What next steps should I take? If you see this message, you can either wait or go back into your network settings and manually connect to your 2.4 GHz home network. Then, go back to the Frigidaire app. Appliance added! App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. This should automatically detect the connected appliances.

If you are unable to resolve an issue or need more information, please contact us. Depending on your model, you may want to use the “Wrinkle Release” or “Extended Tumble” options. Clothes need room to tumble freely. As soon as the cycle is complete, hang or fold your items. To remove wrinkles from clean, dry clothes, select “Instant Refresh” cycle (available on some models) or tumble them on low heat for 10 or 15 minutes. You can fasten these items or turn garments inside out to reduce the sounds. If you think this is the issue, stop the dryer and check for any objects in the drum. If none are present and the sounds continue, we recommend running an empty load to see if the noise continues. This will allow you to determine if the noise is coming from the unit or an article that was being dried. If the noise is still present during the empty load, please contact us. Can I do anything about this? You can also periodically wash the lint screen in warm, soapy water to remove any residue, and then dry it thoroughly before replacing. Note: Do not operate the dryer without the lint screen in place, as this could damage it. If the Air Fluff cycle or temperature is selected, the dryer will tumble without heat. Generally you’ll want to select low or medium heat, and the Normal Dry setting. Select More Dry for loads requiring more time. A medium or low heat setting is safe for permanent press, delicate, and knit items, but will require longer drying periods. If your dryer is overloaded or too empty, it will take longer to dry your clothes. Items need room to tumble freely in order to dry well, and you also need enough items in the drum for proper tumbling. Dry items of similar fabric and weight in the same load. Drying times will be longer in areas where humidity is high. You can use a dehumidifier near the dryer if needed. To locate the moisture sensor bars, please refer to your Complete Owner’s Guide.

Fabric softener sheets can leave a residue on the moisture sensor bars in the dryer, which can inhibit their ability to accurately sense wet clothes. Remove the residue by wiping the moisture sensor bars with rubbing alcohol. If your dryer is installed in a closet or under a counter, it might not be getting the ventilation needed for proper drying. Be sure the exhaust duct is not clogged. If the problem persists, consider having it cleaned by an authorized service provider. Note: To avoid the risk of carbon monoxide poisoning, never operate a gas dryer without an exhaust duct that vents outdoors. Use an approved vent hood with a swing-out damper that opens when the dryer is in operation and closes automatically when the dryer stops. Do not attach a screen over the vent hood opening, and maintain a minimum clearance of 12 inches between the bottom of the vent hood and the ground. Using 208-volt can increase drying times. Refer to the Installation Instructions. What should I do? If one of these is tripped or blown, the drum may turn but the heater will not operate. If this is the case, you’ll need to reset the circuit breaker or replace the house fuse. Check the cycle selector—if the Air Fluff cycle or temperature is selected, the dryer will tumble without heat. Be sure the gas supply valve to gas dryer is open. (See Installation Instructions for details). If you have a gas dryer and your LP gas tank is empty, refill or replace the tank. If there has been an interruption in the natural gas supply, call your natural gas company. The dryer needs space around it for proper ventilation to support the gas burner. Do not stack or place laundry or rugs against the front or back of the dryer. To install a dryer in a closet or alcove, please refer to the Installation Instructions. Overloading the dryer can cause its motor to overheat. If this is the case, allow the motor to cool down for 30 minutes.

App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Here are some simple tips: Dehumidifier named “Dehumidifier” App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Here are some simple tips: App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Hold times are long. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Simply select the category below for the product manual, user guide or specifications document you would like to receive. Optional Features. Newest Added: PTH094G35AXXX AMAP081AW FFTR1821TB ABB1924BRM PTH123G35CXXX Installation. Normal Operating Sounds and Sights. Care and Cleaning. Handle Installation. Before you Call. Connecting Water Supply. Major Appliance Warranty. Ice Service. IMPORTANT SAFETY INSTRUCTIONS Installation Checklist Please read all instructions before using this refrigerator. ? Handles are secure and tight For your Safety. Freezer door is level across the top flammable liquids in the vicinity of this or any other appliance. Toe grille is properly attached to refrigerator. Staples ? Refrigerator plugged in can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture. Definitions Ice Maker. House water supply connected to refrigerator. No water leaks present at all connections - recheck in 24 hours This is the safety alert symbol. It is used to alert you to potential personal injury hazards. ? Ice maker is turned ON. Front filter must be flush with filter symbol to avoid possible injury or death.Shipping material removed.

Fresh food and freezer temperatures set DANGER indicates an imminently hazardous situation whi Frigidaire - Refrigeration Mon-Fri, 8:30am - 8pm (EST) Twitter Fan Page Website Correct it, if wrong. Page Count: 31 Read product labels for warnings regarding flammability and other hazards. DO NOT operate the refrigerator in the presence of explosive fumes. Avoid contact with any moving parts of automatic ice maker. Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture. Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation. Proper Disposal of your Refrigerator or Freezer Risk of child entrapment Child entrapment and suffocation are not problems of the past. If you are getting rid of your old refrigerator or freezer, please follow the instructions below to help prevent accidents. Check with your utility company or visit www.recyclemyoldfridge.com for more information on recycling your old refrigerator.Have refrigerant removed by a qualified.Do not use an extension cord or adapter plug. If the power cord is damaged, it should be replaced by an authorized service technician to prevent any risk. Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord. Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock. Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.

Do not plug the unit into an electrical outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Avoid connecting refrigerator to a Ground Power cord with 3-prong grounded plug To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change. Before starting the refrigerator, follow these important first steps, Location - Choose a place that is near a grounded, non-GFCI, electrical outlet. The compressor will not be able to maintain proper temperatures inside the refrigerator. Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator. Installation - Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrica. Door opening The refrigerator doors are designed to shut by themselves within a 20 degree opening. Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of refrigerator drawers and freezer baskets, the refrigerator should be in a position where both can be fully opened. To level the cabinet using the front rollers (select models): 1 Slightly open freezer drawer.If gasket is not sealed, open drawer and slightly loosen four (4) drawer screws (two (2) on each side) to allow drawer to rotate. Drawer Close drawer and recheck the seal on the gasket (A). Open the drawer grabbing by the sides in the center (B). Push Freezer Drawer i Be careful not to rotate the drawer.

Doors should align with each other and be level. Most of these conditions can be met by raising or lowering the adjustable front rollers, To level the cabinet using the front rollers: 1 You can raise or lower each door. To raise: turn adjustment screw clockwise. To lower: turn adjustment screw counterclockwise. 2 Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable. 3 After unit is leveled, lower anti-tip leg until it contacts the floor.To level the doors using the adjustable lower hinge (select models): 1 Remove all food items from door bins on door being adjusted. 2 Open doors to 90 degrees. 3 Loosen or remove screw.To raise the door, rotate washer clockwise (when viewed from the bottom). To lower door, rotate washer counter-clockwise when viewed from the bottom). Screw will not be tight, just insert until it is flush with the hinge. Screw To adjust the flipper mullion: 1 Loosen the screw located on the flipper mu!lion hinge. Adjusting Flipper Mullion Screw 2 Adjust flipper mullion height. For proper connection with the flipper mullion guide, there should be a separation about the thickness of a coin (0.060 inches, or 1.5 mm) between the guide and flipper mullion. Adjusting Flipper Mullion Height 3 Re-tighten screw. Check first by measuring the entrance. To prepare for removing the doors: 1 Make sure the electrica. To remove the top hinge covers: 1 Remove the two (2) screws from each cover over the top door hinges. 2 Lift inside edge of hinge cover and tilt back. This makes reinstallation easier. 2 Disconnect the harness by grasping both sides of the connector firmly, depress the latch, and pull apart. Remove the two (2) screws from the top hinge. Lift the door off of the bottom hinge and set it aside. 3 Detach the water tube from the connector located behind the refrigerator and pull the tube back out to the front of the unit.

The connector releases when you press inward on the outer sleeve while pushing the tube toward the connector then while continuing to hold in the sleeve, pull the tube away. DO NOT remove the ground screw from hinge. To reinstall the right door, reverse the above steps. Be sure doors are set aside in a secure position where they cannot fall and cause personal injury, or damage to the doors or handles. Removing Freezer Drawer 1 Open freezer drawer. 2 Remove drawer screws on right and left sides (two (2) screws on each side). Drawer is heavy. Use caution when lifting. 3 Lift drawer up and out to remove. Installing Freezer Drawer 1 With lower slides pulled out, hang drawer onto slide brackets ensuring pins on each side are fully inserted into slots on each side.If gasket is not sealed, open drawer and slightly loosen four (4) drawer screws (two (2) on each side) to allow drawer to rotate. Close drawer and recheck the seal on the gasket (A). Be careful not to rotate the drawer. Push Against Freezer Drawer 6 Tighten four (4) drawer screws. 7 Recheck gasket sea!. 8 Install the toe grille by fitting into place. All set screws should be tightened so the screw is below the surface of the handle. The handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the opposite door while tightening the Allen screw makes installation easier. The door handle may loosen over time or if it was installed improperly. If this happens, tighten the set screws on the handles. Mounting Refrigerator Handles Mounting Freezer Handle G While holding handle firmly against door, loosely tighten far right Allen set screw (B) with supplied Allen wrench until there is no gap between handle and door. 7 Still holding the handle firmly to the door, firmly tighten far left Allen set screw (B) with supplied Allen wrench. 8 Return to the far right Allen set screw (B) and firmly tighten with supplied Allen wrench. 9 Firmly tighten the inside Allen set screws.

frigidaire refrigerator manuals online

Try adjusting the humidity control for more air flow The display will show “Sb” while in Sabbath mode. Repeat the steps above to deactivate. Some things to keep in mind when your refrigerator is in Sabbath mode: The ice cube compartment will remain cold. For example, if you inadvertently left the refrigerator door open for a period of time, the HIGH TEMP alarm will signal for safety reasons.Also, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the ice bin to fill completely. The ice bin will hold about 4 pounds of ice. Set the freezer control to a colder setting to improve ice production. Allow 24 hours for the temperature to stabilize. Sometimes an ice cube or other object may be preventing the signal arm from freely moving. Additionally, ensure the ice bin itself is pushed all the way to the rear of the shelf. If this comes slightly out of place, it may prevent the signal arm from dropping all the way down and producing ice as it should. Feel free to discard the ice and allow a fresh supply to be produced. TIP: Ice production should be used at least twice a week to keep the cubes separated. This usually is due to the water filter being clogged or a restricted water supply. It is recommended to change the water filter first but if the condition still occurs then you want to check for a saddle valve, water valve not turned on all the way or kinked water supply line. Remember, smaller ice cubes or ice chips jamming in the ice maker may be a sign that your water filter needs changing. As the water filter becomes older (6 months or more) it can become clogged with particles and less water is delivered to the ice maker. The ice maker can’t fill every cube in the ice maker mold, leading to small cubes or ice chips that can get caught between the ice ejector blades and the stripper.

• frigidaire refrigerator manual online, frigidaire refrigerator manuals online, frigidaire refrigerator manuals online, frigidaire refrigerator manuals online, older frigidaire refrigerator manuals online.

We appreciate your patience. For Side-by-Side, French-Door and Multi-Door refrigerators, the model and serial number can be seen along the upper right side of the fresh food compartment and is visible when the door is opened. You will also have easy access to your warranty information and product care tips. To register your product, you will need your Model and Serial number and date of purchase as shown on your receipt. You can register on-line. You can also drop your product registration card in the mail. If you have any questions, please contact us. Plus, you get all of the features and quality you expect. For more information, see: www.energystar.gov The label will tell you about the product's efficiency level, including approximately how much energy the appliance uses, its average annual operating cost, and how its energy use compares with that of similar products. For more information, see: However, most of your refrigerator can simply be cleaned using soap, water and a soft cloth. Be sure to wring excess water out of the sponge or cloth before cleaning around controls, light bulb or any electrical part. It provides streak-free shine, protective coating repels dust and dirt, and gently cleans tough stains. Wipe with the grain to prevent scratching. Always follow the manufacturer’s instructions when using. Is this normal? It is normal for the compressor to go on and off frequently. The thermostat keeps the refrigerator at a constant temperature. Single speed compressors (most Top-Freezer and Side-by-Side refrigerator models) Allow 24 hours for the temperature to stabilize. At times it may even run faster, such as after a defrost cycle. It is preferred that you do not adjust the temperature from the recommended setting during the 1st 24 hours. If you have any questions, please contact us. Here are some helpful tips: This keeps incoming air to a minimum and maintains maximum moisture.

Remember to order the same filter that is currently in your refrigerator. If you have any questions, please contact us. It is always recommended to check out your Owner’s Manual for more descriptions of these features and when best to use. Press selection directly on display for a few seconds until you hear an audible tone. If deactivating a selection, the LED light will no longer illuminate. If you have any questions, please contact us. The drawer automatically defaults to a locked state to prevent any unwanted use. To change the drawer’s settings, simply press Unlock and hold for 3 seconds. To change the drawer temperature when in the freezer temp setting, use the control panel display on the front door of your Multi-Door refrigerator. It’s important to note, when changing the temperature on the display, you will be changing both the drawer temperature setting AND the freezer compartment.Auto CrispSeal TM Drawers may be equipped with an automatic humidity control membrane. We do not recommend replacing the auto-humidity membrane unless it becomes damaged or dirty. If the membrane requires cleaning, it can simply be washed with soap and water. Make sure you thoroughly dry the membrane before replacing in your refrigerator. For further instructions regarding how to remove the auto-humidity membrane, check out your Owner’s Manual. If you have any questions, please contact us. To adjust your shelves: Lower the shelf into the desired slot and lock into position The shelves slide out independently of their mounting brackets. Just pull the front of the shelf forward. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. To change the position of an adjustable door bin simply: If you have any questions, please contact us.It is always recommended to check out your Owner’s Manual for more descriptions of these features. Use the UP or DOWN key to scroll through the menu that appears in the center of your display.

If you have any questions, please contact us. Air in new plumbing lines can result in an uneven water flow. To reset the shutoff device, simply release the dispenser paddle and then resume if needed. This is perfectly normal. Press and hold the lock key on your display for 3 seconds to unlock. The dispenser has a built-in device that shuts off after 3 minutes of continuous use to prevent the motor from overheating. To reset the shutoff device, simply release the dispenser paddle and then resume if needed. Remove the ice bin, thaw and empty contents. When new ice is produced, dispenser should operate. Take out the ice bin completely and remove the ice cubes. Replace the bin and the dispenser should operate. If the auger is accidentally rotated, you must realign the auger by turning it in 45 degree turns until the ice bin fits into place.Press and hold the lock key on your display for 3 seconds to unlock. The water filter may be clogged or overdue for replacement.However, air can be trapped in the new plumbing lines which can result in 2 or 3 empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. It will also prohibit the water to evenly flow initially from the dispenser. It may take about 1-2 minutes. Most Owner’s Manuals will provide you the water filter information specific to your model.On most models, the Water Filter Status on your display will illuminate and prompt you when it’s time to replace the filter. If your refrigerator has not been used for a period of time (during moving for example), it is recommended to change the filter before reinstalling the refrigerator. Remember to order the same filter type that is currently in your refrigerator. If you need more help, please contact us. Replacing the air filter will ensure optimal filtering of refrigerator odors. You may want to adjust this time period depending on the types and amounts of food you typically store in your refrigerator.

You will also need to provide the date of purchase as shown on your receipt. It’s always a good idea to save this information. If you have any questions, please contact Frigidaire at 1-800-374-4432. They’re perfect for storing laundry supplies, extra towels, cleaning supplies and more. They can also ensure your washer is at the optimal height for loading and unloading. Or you can check your model here or find it in your Installation Guide, which is also available online. To earn the Energy Star rating, products must meet strict energy efficiency criteria set by the U.S. Environmental Protection Agency or the U.S. Department of Energy. These products can help save money on your electricity bill and protect the environment by reducing harmful emissions from power plants, as well as providing all the features and quality you expect. This label signifies that the product passed stringent standards set by the U.S. Department of Energy. Additionally, manufacturers are required to display their product’s test results on the Energy Star label. The label will tell you about the product’s efficiency level, including approximately how much energy the appliance uses, its average annual operating cost and how its energy use compares with that of similar products. Your Complete Owner’s Guide will give you more information on those applicable to your model. You can also wash the lint screen in warm, soapy water to remove any residue, and then dry it thoroughly before replacing. Push or turn the start button and hold it for two seconds. To be sure it’s correctly positioned, simply turn the knob until the indicator is a little further into the cycle. The door must be completely closed for the dryer to run. Check to be sure the plug fits tightly into the wall outlet. Note: Do not use an extension cord. If this is the case, reset the circuit breaker or replace the fuse (but do not increase the fuse capacity).

When selection is made, go back and press OPTIONS to save. To adjust your shelves: Lower the shelf into the desired slot and lock into position The shelves slide out independently of their mounting brackets. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. To change the position of an adjustable door bin simply: If not aligned on either side, push the basket sideways until it is aligned. It is always recommended to check out your Owner’s Manual for more descriptions of these features. When selection is made, go back and press OPTIONS to save. Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. Door reversal instructions can be found in your Installation guide. You may hear the sides lock into the tabs. No worries, just discard the ice made during the 1st 24 hours and then you should be good to go. NOTE: If the ice maker is ON and the water supply is not connected, the water valve will make loud chattering noises. Adjusting refrigerator control changes temperatures in both the refrigerator and the freezer. Adjusting the refrigerator control changes temperatures in both the refrigerator and the freezer. To maintain temperatures, a fan circulates air in the refrigerator and freezer and therefore, it is important not to block air vents with food items. This could disrupt the air flow and cause temperature issues. For some models: Adjusting the refrigerator temperature control “0” turns off the compressor and prevents the refrigerator from cooling but does not disconnect the power to the light and electronics. To completely turn off your refrigerator, you must unplug it. We appreciate your patience. The large capacity and fast dry times of our newer models save on energy use and time. Once you have registered, you will receive useful information including easy access to your warranty and product care tips.

If letting the motor cool down and reducing the load size does not resolve the issue, contact your authorized service provider. On electric dryers, a thermal limiter switch automatically turns off the motor in the unlikely event of an overheated situation. If this is the case, you’ll need to contact a service provider to replace the thermal limiter switch. How can I prevent this? Try using the Auto Dry cycle instead of a Timed Dry cycle, and follow care instructions on the fabric labels. For best results, follow these suggestions. We appreciate your patience. App store is a service mark of Apple Inc. Google Play is a trademark of Google Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Serial numbers beginning with KK0, KN0 or XK0 should use the 2.0 app. All others should use the original Frigidaire Smart Appliance app. The Frigidaire - Smart Appliances app is for older appliances and will be kept active until we migrate those existing customers to the new Frigidaire 2.0 app in late 2020. Once migration is complete, users will be notified to download the latest version of the app. Standard text rates may apply if you opt to receive text message notifications. App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. You will be prompted to enter your email address and you will be sent a link to reset your password. NOTE: Your account through the Frigidaire app is different from an account created on www.Frigidaire.com. The good news is that as soon as power is restored, the appliance will should automatically re-connect and function normally without user intervention. You may receive a “connection lost” notification in the Frigidaire app. You will use the same email address and password that you used during the initial set up.

Before doing so, the smart appliance will need to be removed from the Frigidaire app and taken through a Factory reset to clear the memory. To conduct the Factory reset, follow the steps listed below: You can then create a new account using a valid email address and password of at least 6 characters and one number (no spaces). Once you have accessed the Frigidaire app, press “Add My First Appliance” so you can be led through the connection steps. App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. What can I do? If it’s not, you will need to add a password Some dual-band or mesh networks may need to be manually switched to a 2.4 GHz network. Please contact your network provider if you are unsure of your network type. However, you will need to use the same email and password to login. What can I do to fix this? The schedule can be controlled from the Frigidaire app, and the appliance will keep the last known schedule in its memory until the schedule is turned off. The previous schedule will remain in the appliance’s memory until a new schedule is set. If this is not done, the appliance will continue to run on the last programmed schedule. What should I do? This is normal and you should be able to move forward. If the phone does not stay connected to the network, try checking your network settings for features like “Smart Network Switch”, “switch to mobile data” or “avoid weak networks”. If these features are active, they may impede the connection and should be temporarily turned off. What next steps should I take? If you see this message, you can either wait or go back into your network settings and manually connect to your 2.4 GHz home network. Then, go back to the Frigidaire app. Appliance added! App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. This should automatically detect the connected appliances.

If you are unable to resolve an issue or need more information, please contact us. Depending on your model, you may want to use the “Wrinkle Release” or “Extended Tumble” options. Clothes need room to tumble freely. As soon as the cycle is complete, hang or fold your items. To remove wrinkles from clean, dry clothes, select “Instant Refresh” cycle (available on some models) or tumble them on low heat for 10 or 15 minutes. You can fasten these items or turn garments inside out to reduce the sounds. If you think this is the issue, stop the dryer and check for any objects in the drum. If none are present and the sounds continue, we recommend running an empty load to see if the noise continues. This will allow you to determine if the noise is coming from the unit or an article that was being dried. If the noise is still present during the empty load, please contact us. Can I do anything about this? You can also periodically wash the lint screen in warm, soapy water to remove any residue, and then dry it thoroughly before replacing. Note: Do not operate the dryer without the lint screen in place, as this could damage it. If the Air Fluff cycle or temperature is selected, the dryer will tumble without heat. Generally you’ll want to select low or medium heat, and the Normal Dry setting. Select More Dry for loads requiring more time. A medium or low heat setting is safe for permanent press, delicate, and knit items, but will require longer drying periods. If your dryer is overloaded or too empty, it will take longer to dry your clothes. Items need room to tumble freely in order to dry well, and you also need enough items in the drum for proper tumbling. Dry items of similar fabric and weight in the same load. Drying times will be longer in areas where humidity is high. You can use a dehumidifier near the dryer if needed. To locate the moisture sensor bars, please refer to your Complete Owner’s Guide.

Fabric softener sheets can leave a residue on the moisture sensor bars in the dryer, which can inhibit their ability to accurately sense wet clothes. Remove the residue by wiping the moisture sensor bars with rubbing alcohol. If your dryer is installed in a closet or under a counter, it might not be getting the ventilation needed for proper drying. Be sure the exhaust duct is not clogged. If the problem persists, consider having it cleaned by an authorized service provider. Note: To avoid the risk of carbon monoxide poisoning, never operate a gas dryer without an exhaust duct that vents outdoors. Use an approved vent hood with a swing-out damper that opens when the dryer is in operation and closes automatically when the dryer stops. Do not attach a screen over the vent hood opening, and maintain a minimum clearance of 12 inches between the bottom of the vent hood and the ground. Using 208-volt can increase drying times. Refer to the Installation Instructions. What should I do? If one of these is tripped or blown, the drum may turn but the heater will not operate. If this is the case, you’ll need to reset the circuit breaker or replace the house fuse. Check the cycle selector—if the Air Fluff cycle or temperature is selected, the dryer will tumble without heat. Be sure the gas supply valve to gas dryer is open. (See Installation Instructions for details). If you have a gas dryer and your LP gas tank is empty, refill or replace the tank. If there has been an interruption in the natural gas supply, call your natural gas company. The dryer needs space around it for proper ventilation to support the gas burner. Do not stack or place laundry or rugs against the front or back of the dryer. To install a dryer in a closet or alcove, please refer to the Installation Instructions. Overloading the dryer can cause its motor to overheat. If this is the case, allow the motor to cool down for 30 minutes.

App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Here are some simple tips: Dehumidifier named “Dehumidifier” App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Here are some simple tips: App store is a service mark of Apple Inc. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Hold times are long. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Frigidaire Fridge Manual. To get started finding Frigidaire Fridge Manual, you are right to find our website which has a comprehensive collection of manuals listed. Our library is the biggest of these that have literally hundreds of thousands of different products represented. I get my most wanted eBook Many thanks If there is a survey it only takes 5 minutes, try any survey which works for you. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Frigidaire Freezer Owners Manual File Type Pdf. To get started finding Frigidaire Freezer Owners Manual File Type Pdf, you are right to find our website which has a comprehensive collection of manuals listed. You may be having an issue with your fridge because the refrigerator door was left open, the freezer won’t freeze, the refrigerator is leaking, the ice maker is not working, water dispenser not working, fridge is showing error codes, unable to change temp controls, fridge clicks, does not get cold, etc.

You need to find a refrigerator service manual or repair data sheet to show you how to diagnose the problem and what needs to be fixed or replaced. These free repair service manuals are for all types of refrigerators including french door, mini fridge, freezer in bottom, water and ice dispensers, side by side, and front control panel and display models refrigerators. Below we have researched links that will help you to either download a free.pdf refrigerator service repair manual or view it online in your web browser. Don’t need a service technician manual. Look here for help with fixing your refrigerator that won’t cool. The Refrigerator Model number is usually located in the refrigerator or freezer side wall, behind the crisper, behind the kick plate, or on the fridge ceiling.When your refrigerator breaks down, finding your service manual is the best way to troubleshoot and fix the problem. Why pay for an appliance repair company to tell you what needs to be replaced. With a service or owners manual, you can obtain information about the problem before you decide if you want to hire an appliance repair company to get the refrigerator fixed or try and fix it yourself. Contact here When I am away for few days its a challenge if there is a power outage as I would find it still “off” though power back and stuff spoilt inside. It used to work perfectly fine. It is also noisy though its balanced. Notify me of new posts by email. Learn how your comment data is processed. Dryer Repair How To Clear The Cache On Your Xbox? How To Check Clothes Dryer Vent Hose Air Flow AC ON vs AC OFF Mens And Womens Shoe Size Conversion Chart Learn How To Buy And Sell Do Not Pay To Watch Your Favorite Movies And TV Shows Here Is The Info You Need For Replacement How To Easily Clean A Dirty Oven That Has Never Been Cleaned How Long Does Wall Paint Take To Dry? Replacement Information Here Decode CC Digits Wall Or Bed Frame? Glue Guide Chart Here Is What To Check Yourself!

Most Important Things For Job Interview We aim to always deliver relevant and engaging content where facts and information provided is checked and rechecked for accuracy. Note: Any images or third-party logos on this page belong to their respective copyright holders and are used for informational purposes only.We may receive compensation when you click on links to those products. Simply select the category below for the product manual, user guide or specifications document you would like to receive. Page Count: 32 Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Child Safety Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.Operating the refrigerator with insufficient power can damage the compressor. CFClHCFC Disposal Pressing and holding the OnlOff button for Your old refrigerator may have a cooling system three seconds, located on the temperature that used CFCs or HCFCs (chlorofluorocarbons control panel (Electronic controls), or or hydrochlorofluorocarbons). Other refrigerants your refrigerator's cooling system, but does may also cause harm to the environment if not disconnect the power to the light bulb released to the atmosphere, and other electrical components. To turn off If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician.

If you intentionally release refrigerant, you may be subject to fines and imprisonment under These guidelines must be followed to ensure that safety mechanisms in this refrigerator will operate properly. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Avoid connecting power to your refrigerator you must unplug the power cord from the electrical outlet. Shelves may break suddenly if nicked, scratched, or exposed to sudden Location Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug. If you do not hook up water to the refrigerator, remember to turn the ice maker off. Toe Grille Installation and Removal To install toe grille 1 Open both doors. Slide left and right sides of toe grille over lower hinges of refrigerator. 2 While pushing toe grille firmly against cabinet, fasten bottom clips of toe grille to cabinet. 3 Fasten top clips to cabinet. 4 Close the doors. Fasten right and left side clips into groove of bottom hinge. The compressor will not be able to maintain proper temperatures inside the refrigerator. Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator. Press firmly on top of toe grille until top of toe grille pops off. Pull toe grille outward toward your body and off of lower hinges. Removing Toe Grille If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be Your refrigerator should be positioned to allow easy access to a counter or table when removing food.

For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened. Guidelines for final positioning of your refrigerator: All four corners of the cabinet must rest firmly on the floor. The cabinet should be level at the front and rear. Doors should align with each other and be level. All of these conditions can be met by raising or lowering the adjustable front rollers. Raise To level the doors using the adjustable lower hinge (some models): Before leveling either door, remove set screw that locks door height into position. (The door cannot be adjusted without set screw removed). Reinstall set screw, locking the door height.Rear Cover Float cover Screw Screws Top I i Cover i I I I Hinge Screws Top,Hinge To remove the refrigerator doer: 1 Trace lightly around the door's top hinge with a pencil. This makes reinstallation easier. To prepare for removing the doors: 1 Make sure the electrical power cord is unplugged from the wall outlet. Open both doors and remove the toe grille (as explained in the Installation Instructions that came with your appliance). 3 Remove any food from the door shelves. Remove the two screws from the top hinge. Lift the door off of the bottom hinge and set it aside. Hinge Adjustable Hinge (some models) To reinstall the refrigerator door, reverse the above steps. To remove the freezer top hinge cover: i Remove the two screws from each cover over the top door hinges. 2 Lift hinge cover straight up and off. The connector releases when you press its outer sleeve inward. Remove the screws from the top hinge and pull the multi-wire cable through it. Lift the door off of the bottom hinge. Remove the two bottom hinge screws and hinge if necessary.

frigidaire refrigerator manual frt17l3fw1

Leave shelves in place so children may not easily climb contact with other appliances or furniture. inside. CHILD SAFETY a?? Have refrigerant removed by a qualified service technician. Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is IMPORTANT unpacked. Children should NEVER use these items to play. Turning the Freezer and Cartons covered with rugs, bedspreads, plastic sheets or Fresh Food Controls to a?? 0 a?? stretch wrap may become airtight chambers, and can quickly turns off the compressor cause suffocation.To turn off power to your refrigerator ELECTRICAL INFORMATION you must unplug the power a?? The refrigerator must be plugged into its own dedicated cord from the wall outlet. 115 Volt, 60 Hz., AC only electric outlet. The power cord of the appliance is equipped with a three - prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three - prong receptacle. The receptacle must be installed in accordance with localcodes and ordinances. Consult a qualified electrician. Do not use an extension cord or adapter plug.Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.Before starting the floor. Your refrigerator is equipped with adjustable front rollers refrigerator, follow these important first steps.Use sources. adjustable wrench to a?? The refrigerator must be installed on a floor that is level adjust leveling screws.TTNNOOTTEEETEE NNONOO INSTALLATION Raise the front of the refrigerator enough so the doors close freely when opened halfway. The refrigerator should slope A? a?? OOCCAAUUTTIIOONNNONN to A? a?? from front to back. Then level the refrigerator from side TCAUTITII CCAAUU to side.

• frigidaire refrigerator manual frt17l3fw1.

If you want to search this text, hold control and F, and type the word you are looking for. We Questions ? here at Electrolux Home Products, Inc.It contains valuable information on how to properly maintain your new 1 - 800 - 265 - 8352 refrigerator. ( Canada ) We know youa??ll enjoy your new refrigerator and Thank You for choosing our product. We hope you consider us for future purchases. Use your refrigerator only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, CALL 1 - 800 - 944 - 9044 operating and maintaining any appliance. To Enjoy These Benefits: Please record your model and serial numbers below for future reference. This information is found on your serial plate located inside the refrigerator compartment.TTNNOOTTEEETEE NNONOO a?? Fast, convenient toll - free service is just a Use only soap and water to clean serial plate.Model Number: a?? Quickaccesstogenuinereplacementparts Serial Number: so you can rest assured your refrigerator is Purchase Date: repaired with the proper components. Please attach sales receipt here for future reference. PLEASE COMPLETE AND MAIL IN THE PRODUCT REGISTRATION CARD INCLUDED WITH YOUR REFRIGERATOR. 2 Page: 3 IMPORTANT SAFETY INSTRUCTIONS PROPER DISPOSAL OF YOUR REFRIGERATOR OR NNWWAARRNNIINNGGGNGG NWARNINII FREEZER WWAARR Please Read All Instructions Before Using This Risk of child entrapment Refrigerator. Child entrapment and suffocation are not problems of FOR YOUR SAFETY the past. Junked or abondoned a?? Do not store or use gasoline, or other flammable liquids refrigerators or freezers are still in the vicinity of this or any other appliance. Read product dangerous a?? even if they will sit labels for warnings regarding flammability and other for a?? just a few days. a?? If you are hazards.Staples can cause a?? Remove doors. severe cuts, and also destroy finishes if they come in a??

To determine the length of copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet ( 2.1 meters ), so the refrigerator can be moved out for cleaning ( as shown ).DO NOT use a self - piercing type shutoff valve.TTNNOOTTEEETEE NNONOO IMPORTANT Water line kit number 5303917950, available from your It takes approximately 24 hours for the ice maker to begin appliance dealer at additional cost, contains 25 feet ( 7.6 producing ice. Air in new plumbing lines may cause ice meters ) of A? inch OD copper tubing, a saddle type shutoff maker to cycle two or three times before making a full tray of valve ( nonpiercing ), ( 2 ) A? inch brass compression nuts, ( 2 ) ice. The direction in which your refrigerator doors open ( door swing ) can be reversed, from left to right or right to left, by moving the door hinges from one side to the other. Reversing the door swing should be performed by a qualified person. IMPORTANT Before you begin, turn the refrigerator temperature control to a?? 0 a?? and remove the electrical power cord from the wall outlet. Set door aside. 3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure plastic washer stays on hinge pin. 4. Lift refrigerator door off of bottom hinge and set aside. 5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge and shim to slide out. Move hinge pin to other hole in hinge and tighten with adjustable wrench. 10. Reverse door handles ( see instructions on next page ). 11. Move freezer and refrigerator door stops to opposite side. Before starting screws, use an awl to puncture the foam. 12. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door. Close refrigerator door to help align hinge hole. 13. Tighten center hinge pin with adjustable wrench. 14.

The compressor will not be able to maintain proper temperatures inside the refrigerator. Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator. DOOR OPENING TTNNOOTTEEETEE NNONOO If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider. Your refrigerator should be positioned to allow easy access to a counter when removing food. To make this possible, the direction in which the doors open can be reversed. Disconnect refrigerator from electric power source. To avoid electric shock, which can cause death or severe 2. Place end of water supply line into sink or bucket. Turn ON personal injury, disconnect the refrigerator from electrical water supply and flush supply line until water is clear. Turn power before connecting a water supply line to the OFF water supply at shutoff valve.Tighten another a?? Copper tubing is recommended for the water supply half turn with a wrench; DO NOT over tighten. line. Water supply tubing made of A? a?? plastic is not 6. With steel clamp and screw, secure water supply line to recommended since it greatly increases the potential rear panel of refrigerator as shown.Coil excess water supply line ( about 2 A? turns ) behind line.If the ice maker is connected 9. Reconnect refrigerator to electrical power source.To turn ice maker on, lower wire signal arm ( see ice and working properly. IMPORTANT Ensure that your water supply line connections comply with all local plumbing codes. Before Installing The Water Supply Line, You Will Need a?? Basic Tools: adjustable wrench, flat - blade screwdriver, TM and Phillips screwdriver a?? Access to a household cold water line with water pressure between 30 and 100 psi.

For models with short handle trim, remove by sliding trim 2. Secure handle to straight down and off of handle bracket. Slide both trim locks out of trim. ( Handles may be easier to reverse while doors are off. ) 2. Insert new adhesive trim locks contained in your literature Figure 1 Style Handles pack. 1. Remove two screws attaching handle to top of refrigerator TTNNOOTTEEETEE NNONOO door. 2. Remove screw attaching bottom of handle to door. Trim lock must be removed and installed by sliding over the 3. Remove two hole plugs and hinge pin plug on top of door two donut shaped areas.Use Phillips head screwdriver to remove plastic screw plug from front of door and install 3. Install trim to handle by sliding under base of handle.TO ATTACH REFRIGERATOR HANDLE: Figure 1 Style Handles 1. Secure bottom of handle with screws. 2. Secure top of handle with screws. Figure 2 Style Handles 1. Start with handle offset away from door. Place bottom of handle over dovetail button, swing handle into an upright position and pull upward, locking it into place. 2. Secure top of handle with screws. Figure 1 Figure 2 TO REMOVE REFRIGERATOR HANDLE: REMOVING STAINLESS STEEL DOORS AND HANDLES ( Handles may be easier to reverse while doors are off. ) OOCCAAUUTTIIOONNNONN TCAUTITII CCAAUU 1. Remove two screws attaching handle to top of Use care when using tools near surface of stainless steel refrigerator door.To Remove Doors 3. Remove screw on side of Stainless steel doors are not reversible. Follow these steps to refrigerator door and remove doors.Reverse freezer and top hinge cover.Remove top hinge and shown in figure 3.Set door aside. REFRIGERATOR HANDLE: 3. Unscrew center hinge 1. Secure side of handle to pin using adjustable door and replace plug wrench and save for button. Remove bottom hinge. Reinsert two outside screws in To Remove Handles holes and tighten. 1. Firmly hold freezer handle while loosening set screws 7.

Remove cabinet and hinge hole plugs and move to opposite side. 15. Lower freezer door onto center hinge pin. 16. Close freezer door. Have an assistant lift up on opposite side of door while tightening screws to install top hinge. 17. Replace toe grille. 18. Plug in electrical power cord and turn refrigerator temperature control to center position. Remove two screws attaching handle to bottom of freezer into the sides of the door. On these models, only the hinges door.Magnetic Nameplate Models: Use putty knife to gently pry door.Remove nameplate 2. Remove short trim piece by sliding trim straight up and off from its frame, turn frame upside down and install in old of handle bracket.Self - Adhesive Nameplate Models: Use putty knife to 4. Magnetic Nameplate Models: Gently pry magnetic gently peel off nameplate from door and reapply over old nameplate frame from door. Remove nameplate from its handle holes.Insert magnetic nameplate into frame. HANDLE: Self - Adhesive 1. Start with handle Nameplate Models: offset away from Gently peel off door. Place top of nameplate from door handle over dovetail and reapply over old button, swing handle handle holes.Secure bottom of opposite side, using handle with two same hole as screws removed nameplate. earlier. 2. Attach handle to bottom of door.The top of the trim attaches to the handle bracket ( Figure 1 ) or fits around the base of the handle ( Figure TO REMOVE FREEZER HANDLE: 2 ). An adhesive a?? trim lock a?? is positioned about halfway down. ( Handles may be easier to reverse while doors are off. ) The bottom of the trim is held in place by either an adhesive 1. Remove two screws attaching handle to bottom of freezer trim lock, or a trim lock with two prongs inserted into a hole on door.Remove trim by gently pulling trim lock areas out and handle.When trim is free from door, slide the trim straight down HANDLE: and away from base of handle. 1. Secure side of handle to door and TTNNOOTTEEETEE NNONOO replace button plug.

To Some models have door install, just slide the Special racks or bins that can Item Rack onto any shelf as accommodate gallon - sized shown in the drawing. Special Item Rack plastic drink containers and economy - sized jars and containers. Some racks are CRISPERS ( SOME MODELS ) adjustable for maximum The crispers, located under storage capacity.Wash items in clear general food storage section, water and remove excess is intended for short term Door Rack water before placing them in storage of cheese, spreads, the crispers. Items with strong or butter.Crisper Drawer 11 Page: 12 LOOKING INSIDE ( CONTINUED ) DELI DRAWER ( SOME HUMIDITY CONTROL MODELS ) ( SOME MODELS ) The Humidity Control, Some models are equipped present on some models with a Deli Drawer for storage with crisper drawers, allows of luncheon meats, spreads, you to adjust the humidity cheeses, and other deli items.This can extend the life of fresh vegetables that keep best in high humidity. Deli Drawer Crisper Humidity Control WINE RACK ( SOME MODELS ) TTNNOOTTEEETEE NNONOO The Wine Rack stores bottles of wine, or single two - liter Leafy vegetables keep best when stored with the Humidity plastic bottles of juice or soda Control set on High Humidity, or in a drawer without a pop. To install, slide the Wine Humidity Control. This keeps incoming air to a minimum and Rack onto the shelf with the maintains maximum moisture content.Install on either side of shelf. Wine Rack ICE SERVICE If your refrigerator has an automatic ice maker, it will provide a IMPORTANT sufficient supply of ice for normal use. During the initial startup of your refrigerator, however, no ice will be produced during Your ice maker is shipped with the wire signal arm in the ON the first 24 hours of operation. Automatic ice makers are also position. To ensure proper function of your ice maker, hook optional accessories that may be installed in most models at up water supply immediately or turn ice maker OFF by lifting any time.

Call your local dealer for information.The ice maker produces 2 to 5 pounds of ice every 24 hours depending on usage conditions. Ice is produced at a rate of 8 cubes every 80 to 160 minutes. OOCCAAUUTTIIOONNNONN TCAUTITII CCAAUU TURNING YOUR ICE MAKER ON Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, After the plumbing connections have been completed, the ensure that the softener is maintained and working water supply valve must be opened. Place the ice container properly.Lower the wire signal arm to its a?? down a?? or ON position. New plumbing connections may cause the first production of ice cubes to be ICE MAKER TIPS discolored or have an odd flavor. These first cubes should be a?? Ice cubes stored too long may develop an odd flavor.TURNING YOUR ICE MAKER OFF a?? Occasionally shake the ice container to keep ice To stop the ice maker, lift the separated.The ice maker also whenever the water supply is turned off.If your operating: model has an adjustable a?? Motor running freezer shelf, place the shelf in a?? Ice loosening from tray the lower position, so that the wire signal arm will hit the ice a?? Ice dropping into ice container Ice when the container is full.TTNNOOTTEEETEE NNONOO Rinse well and dry.Operating Sounds and Sights section on page 17.OOCCAAUUTTIIOONNNONN TCAUTITII CCAAUU Do Not place the ice container in your dishwasher.Do not place the a?? Avoid overcrowding the refrigerator shelves. This reduces refrigerator next to heat - producing the circulation of air around the food and results in uneven appliances such as a range, oven, cooling.See the does not occur.This cuts down on moisture build - up Packaging Foods for Freezing inside the unit.Force as much air out of the packages as the door as soon as possible.Trapped air can cause food to dry out, change color, and develop an off - flavor ( freezer burn ).Loading the Freezer a??

FEATURES AT A GLANCE Ice Tray Freezer Light Ice Maker Ice Bucket Fixed Door Bin Freezer Shelf Freezer Control Door Rack Refrigerator Control Features may vary Dairy Door according to model Deli Drawer Cover Tall Bottle Retainer Deli Drawer Half Shelf Snugger Wine Rack Door Bin Full Shelf Special Item Rack Fixed Door Bin Mid Level Light Door Rack Crisper Cover Crisper Drawers Toe Grille TEMPERATURE CONTROLS COOL DOWN PERIOD a?? Adjust temperature gradually: move the knob in small increments, allowing the temperature to stabilize. To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading a?? For colder temperatures, turn the knob towards Colder.For example, if the refrigerator control is TTNNOOTTEEETEE NNONOO turned to a colder setting, the freezer control may have to be adjusted to a warmer setting. Turning the freezer control will When changing control settings, wait 24 hours before change only the freezer temperature.To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, TEMPERATURE ADJUSTMENT do not block cold air vents with food items. TTNNOOTTEEETEE NNONOO When first turning refrigerator on, move refrigerator and freezer controls to which is the recommended initial setting. To turn off power to your refrigerator, you must unplug the power cord from the wall outlet. Refrigerator Control ( some models ) TEMPERATURE ADJUSTMENT GUIDE Turn Refrigerator Control Slightly Towards Colder. If Refrigerator compartment Is Too Warm Turn Refrigerator Control Slightly Towards Cold.If Freezer compartment Is Too Cold Turn Refrigerator Control To 0. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change. SHELF ADJUSTMENT Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. To adjust sliding shelves: 1 Remove shelf by pulling forward to stop position.

2 Lift front edge up and pull out. Replace the shelf on any pair of rails by reversing this procedure. Sliding Glass Shelf Sliding Wire Shelf 10 Page: 11 LOOKING INSIDE ( CONTINUED ) ADJUSTABLE DOOR BINS To adjust cantilever shelves: Some models have adjustable door bins that can be moved to TTNNOOTTEEETEE NNONOO suit individual needs. Cantilever shelves are supported at the back of the To move door bins refrigerator. Cantilever shelves are available in either glass 1. Lift bin straight up. or wire. 2. Remove bin. 3. Place bin in desired 1 Lift front edge up. position. 2 Pull shelf out. 4. Lower bin onto supports Replace the shelf by inserting the hooks at rear of the shelf into until locked in place. Adjustable the wall bracket. Lower the shelf into the desired slots and lock Door Bin into position. TM SpillSafe glass shelves ( some models ) catch and hold TM accidental spills. In some models, the SpillSafe shelves slide TALL BOTTLE RETAINER ( SOME MODELS ) out for easy access to food and for fast cleaning. The shelves slide out independently of the cantilever brackets. Just pull the The Tall Bottle Retainer keeps tall containers in the bin from front of the shelf forward. The shelf can be extended as far as falling forward when opening or closing the refrigerator door.The Tall Bottle Retainer works best with a Bin Snugger. Full Width Cantilever Tall Bottle Retainer ( left ) and Bin Snugger ( right ) Glass Shelf SPECIAL ITEM RACK ( SOME MODELS ) Cantilever Glass Shelf The innovative design of the Fixed and Sliding Special Item Rack allows you to store a six - pack of 12 ounce DOOR STORAGE drink cans, a bottle of wine, a two - liter soft drink bottle, or a Door bins, shelves, and racks are provided for convenient carton of eggs. The Special storage of jars, bottles, and cans. Frequently used items can be Item Rack mounts on the left quickly selected.

Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.Evaporator The flow of refrigerant through the evaporator may Your new high - efficiency refrigerator may make unfamiliar create a boiling or gurgling sound. sounds. These are all normal sounds and soon will become familiar to you. They also indicate your refrigerator is operating B. Evaporator Fan as designed. Hard surfaces, such as vinyl or wood floors, You may hear air being forced through the refrigerator walls, and kitchen cabinets may make sounds more by the evaporator fan.After defrosting, a popping sound may occur. Rigid foam insulation is very energy efficient, but is not a sound insulator. IMPORTANT During the automatic defrost cycle, you may notice a red glow in the vents on the back wall of your freezer compartment. The timer also produces sounds similar to an electric clock. F. Condenser Fan If condenser coils are located underneath your refrigerator as shown in the drawing at the left, you have a condenser fan. You may hear air being forced through the condenser by the condenser fan. G. Compressor Modern, high - efficiency compressors operate much faster than older models. The compressor may have a high - pitched hum or pulsating sound. H. Water Valve If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle. I. Drain Pan ( Nonremovable ) You may hear water running into the drain pan during the defrost cycle. Wipe up any spills immediately and clean both sections at least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not wash any removable parts in a dishwasher. Always unplug the electrical power cord from the wall outlet before cleaning. OOCCAAUUTTIIOONNNONN TCAUTITII CCAAUU a??

Whenmoving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may tear or gouge the floor covering. If the refrigerator has an automatic ice maker, be careful not to move the refrigerator beyond the plumbing connections.Donottouchrefrigeratedsurfaceswithwetordamphands.TTNNOOTTEEETEE NNONOO a?? Turning the refrigerator temperature control to a?? 0 a?? turns off the compressor, but does not disconnect electrical power to the light bulb or other electrical components. To turn off power to your refrigerator, you must unplug the power cord from the wall outlet.Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or, touch the glue residue with the sticky side of tape you have already removed. Do not remove the serial plate. Wipe gaskets with a clean soft cloth.Remove toe grille ( See illustration on Toe Grille page 4 ). Vacuum backside and wipe with sudsy cloth or sponge. Rinse and a?? Mild liquid sprays dry.Rinse with clean water and a soft cloth. Wipe stubborn spots with an Models Only ) ammonia - soaked paper towel, and rinse. Use a non - abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer's instructions. NOTE: Always clean, wipe and dry with the grain to prevent cross - grain scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth. No need to clean unless operating refrigerator under particularly dusty or a?? Condenser Cleaning Condenser greasy conditions, or if there is significant pet traffic in your home. If cleaning Brush is available from Coils is necessary, remove toe grille and use extended vacuum attachment and your dealer. ( Fan - cooled condenser cleaning brush to remove dust build - up from condenser coils ( see a?? Vacuum Cleaner models only ) item a?? J a?? in illustration on page 14 for location ).

Condenser Use the dusting tool attachment on your vacuum to remove dust build - up on a?? Vacuum Cleaner Coils the condenser coils ( black tubes and wires ) attached to the back of air - cooled ( Air - cooled refrigerators only.Wipe water pan with damp Pan cloth.If the refrigerator is operated under particularly dusty or greasy conditions, or if there is significant Defrost Water Pan ( some models ) pet traffic in your home, it may be necessary to periodically clean the condenser for maximum efficiency. Freezer Light Cover Removal REPLACING THE FREEZER LIGHT BULB ( SOME MODELS ) 1. Unplug refrigerator. 2. Wear gloves as protection against possible broken glass. 3. Unsnap light shield as shown. 4. Unscrew and replace old bulb with an appliance bulb of the same wattage. 5. Replace light shield. 6. Remember to plug the refrigerator back in. Refrigerator Mid - Level Light Cover Removal Vacation and Moving Tips a?? Leave refrigerator operating during vacations of 3 weeks or less. Short a?? Use all perishable items from refrigerator compartment. Vacations a?? Turn automatic ice maker off and empty ice bucket, even if you will only be gone for a few days.Long a?? Clean interior thoroughly. Vacations a?? Leave both doors open to prevent odors and mold build - up. Block doors open if necessary.Moving a?? Adjust rollers all the way up to protect them during sliding or moving.For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMERa??S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN.

If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below. This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described or illustrated are subject to change without notice. Canada USA 1.800.668.4606 1.800.944.9044 Electrolux Canada Corp. It may save you time and expense. This Common list includes common occurrences that are not the result of defective workmanship Occurrences or materials in this appliance.Reset circuit breaker. Refrigerator does not run.Wait 20 minutes and check again.Freezer temperature too cold. Allow 24 hours for the temperature to stabilize. Refrigerator temperature is satisfactory. Refrigerator temperature too cold.Allow 24 hours for temperature to stabilize. Then check freezer temperatures and adjust as needed. Freezer temperature is satisfactory.Odors in refrigerator.Cabinet light not working.Push in light switch, located on the refrigerator control box, to release.Automatic ice maker not working. All of our owner's manuals are in pdf format and can be opened using Adobe's Acrobat or some other pdf reader. You may then print out the Frigidaire FRT17L3FW1 Top Mount Refrigerator manual or just save it to your device for safe storage. If you are unable to open or download the manual then please use the HELP link up above for assistance. Hold times are long. Attaches to the inside of the fridge; designed to hold smaller items such as condiment bottles.

Turn the dial on the timer clockwise to advance it into and out of defrost. Comes with mounting block. When the evaporator fan motor fails, it often generates a lot of noise in the freezer area. If the freezer is cold, but the refrigerator is warm you could have a problem with the defrost system. If so, the evaporator coils will be iced over and this thermostat kit may be defective. Includes icemaker that makes 8 radius ice cubes, water valve, water line, ice bucket and hardware. The terminal orientation on this thermostat may be slightly different than the original. If the gasket is defective, cold air will leak out of the refrigerator. As a result, the refrigerator may run longer than normal, or frost may accumulate inside of the refrigerator. Since 1912, we've learned to recognize the most common problems.Do any of these look familiar. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Learn about our response to Covid-19 It takes 15-30 minutes to fix on average. The instructions below from DIYers like you make the repair simple and easy. So, if your FRT17L3FW1 refrigerator excessive frost, frost on back wall or ice buildup, the following info will help you identify the problem. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. You will also have easy access to your warranty information and product care tips. To register your product, you will need your Model and Serial number and date of purchase as shown on your receipt. You can register on-line. You can also drop your product registration card in the mail. If you have any questions, please contact us. It’s one way our products help make kitchen maintenance virtually effortless.

frigidaire ranges manuals

Surface unit does not heat. No power to the appliance.Surface control knob has not been completely turned to LITE.Pushin and turn the surface control knob to LITE(until burner ignites) and then turn the surface control knob to the desired flame size. Follow instructions under Setting Oven Controls in the Electronic Oven Control section. broiling. Make sure oven door is opened to broilstop position. Meat too close to the element. Reposition the rack to provide proper clearance between the meat and the element. If you have a Frigidaire oven and have misplaced the owner's manual, or are new to your home or apartment and never had a chance to review it, you're in luck. Many of the manufacturer's oven manuals have been digitized and are available online. Properly dispose of all such materials, and keep them out of reach of children. You can damage the oven if you attempt to heat it immediately after bringing it in from a very cold place. Be sure that the outlet you plug it into is the correct voltage and has been installed and inspected by a qualified electrician. Keeping a fire extinguisher on hand and near the appliance (but not so near it will overheat) is a good idea. Be sure that pans and baking dishes will have plenty of room and won't touch the oven top or rack above. Don't overfill baking pans. Inserts catch the fat that renders off meat and prevent it from dripping onto the oven's heating elements. Instead, always place food in an oven-safe baking dish and place it on a rack. Check to be sure that the amount of food in the pan is appropriate for the size of the pan. It will cook more quickly and evenly if it does. Also, the pan's size should correspond to the size of the burner. Don't use a small pan on your cooktop's largest burner. Once it beeps, it has reached its assigned temperature. To put your food into the oven, open the door with caution and place your baking dish inside.

• frigidaire range manuals online, frigidaire cooktop manuals, frigidaire electric range manuals, frigidaire gas range manuals, frigidaire ranges manuals, frigidaire range manuals, frigidaire range manual download, frigidaire range manual pdf.

Please read through the information contained in your literature pack to learn more about your new appliance. Page IMPORTANT SAFETY INSTRUCTIONS. This guide contains important safety symbols and instructions. Please pay special attention to these symbols and follow all instructions given.Some cleaners can produce harmful fumes if applied to a hot surface. Always turn the element off before removing the pan. You may switch from either coil setting at any time. It turns on when the control is set, and stays on until the control is turned off. The hotsurface indicatorlight, located under the glass cooktop,. If a particular food is not listed, start with the medium setting. If more crispness is desired, remove the lid or aluminum foil. There is no need to preheat the oven for roasting meat or baking casseroles. The cooking times and temperatures needed to bake a product may vary slightly from your previously. Preheating Preheating is suggested when searing rare steaks. (Remove the broiler pan before preheating. Foods will stick if placed on hot metal.) To preheat, set the oven control(s) to BROILas instructed in the Owner's Guide. Wait for the element to become red-hot, usually about 2 minutes. Ceramic glass cleaning cream. DO NOT USE ON CERAMIC GLASS COOKTOP Avoid pads, that can leave marks and scratches. A lift-up rod will support the top in its raised position. Only lift the top high enough to allow the support rod to rest in place under the front of the cooktop. To FRAME clean, use hot soapy water and a cloth. Large spillovers can cause heavy smoke or fire when subjected to high temperatures. General Cleaning (contin.ed) Removable Outer Door Glass Panel (some models) Applicable only to models with an external glass panel not held with a frame. This design allows you to clean the inside face of the exterior door panel as well as the hidden face of the door inner glass. Replace or tighten bulb. See Changing Oven Light in this Owner's Guide for instructions.

Joseph, Michigan Your guide to more enjoyable more efficient washdays, RCA Whirlpool home appliances, owner's manual and warranty, Whirlpool Corporation, St. Joseph, Michigan How to enjoy your portable television by RCA Victor, Radio Corporation of America, RCA Victor Television Division, Camden, New Jersey Dream and a promise, kitchens, Whitehead Metal Producsts Company of New York, Inc., New York, New York Here's the automatic washer for me. That's the kitchen I want, Whitehead Monel Kitchens, Household Division of Excel Metal Cabinet Company, Inc., 101 Park Avenue, New York, New York There is a separate leaflet for Eaton Surface Unit Control Switches. Frigidaire Division (Publisher) Material Type manuals (instructional materials) Subjects Kitchen appliances Description Level Item. Please try again.Please try again.Register a free business account Please try your search again later.To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. Instead, our system considers things like how recent a review is and if the reviewer bought the item on Amazon. It also analyzes reviews to verify trustworthiness. Hold times are long. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. No Credit Needed - Low Price Guarantee - Next Day Delivery Freestanding Gas Range gives you more cooking flexibility with a 4.2 cu. ft. capacity oven and Variable Broil and Serve Drawer. The cooktop features four gas 9,000 BTU burners. Ready-select control knobs allow you to easily select options and cooking temperatures. Even Baking technology ensures that food comes out evenly, while the large oven window allows you to easily see what's cooking inside.Dry clothes fast and save time with the Quick Dry Cycle. Meet all of your drying needs.

Be sure to wear oven mitts before handling hot food or putting your hands into the oven. Mitts should always be dry, as wet fabric can conduct heat. Once you've placed your dishes in the oven, close the door and set the timer. Keep an eye on your food, as it may burn before you can smell that it has done so. When your food has finished cooking, remove the baking dish with oven mitts and set it on a hot plate or trivet. Turn off the oven. Many Frigidaire oven manuals specifically forbid these. Instead, use hot water and dish detergent. Wait until the oven is completely cooled before beginning to clean it. Take care when cleaning not to rub, damage or move the gasket. Before using the oven's self-clean cycle, remove broilers, food, baking dishes, utensils or cookware. If the oven has a storage or warming drawer, pull it out and set it to the side. You should also remove the oven racks. She holds a Master of Science in Publishing from Pace University. She owns her own content marketing agency, Wordsmyth Creative Content Marketing (www.wordsmythcontent.com), and she enjoys writing home and DIY articles and blogs for clients in a variety of related industries. She also runs her own lifestyle blog, Sweet Frivolity (www.sweetfrivolity.com). Step-saving U kitchen, designed by Lenore Sater Thye, plans by J. Robert Dodge, Bureau of Human Nutrition and Home Economics, Agricultural Research Administration, United States Department of Agriculture, Washington, D.C. St. Charles custom kitchen styling, St. Thermador Electric Bilt-in Range, Thermador Electrical Manufacturing Company, Los Angeles, California Cooking is fun with your new RCA Estate Electric Range, RCA Estate Appliance Corporation, Hamilton, Ohio Price list of G.B. Knowlton, Fitchburg, Mass., patent agate iron ware and blue and white enameled ware, Fitchburg, Mass. RCA Whirlpool Automatic Dryer, owner's manual and warranty, Whirlpool Corporation, St.

Adjustable Temperature Control allows you to select the correct temperature for your needs. Additionally, stay organized.Freestanding Electric Smooth top Range with Self-Cleaning Oven lets you cook more at once, with a 5.3 cu. ft. capacity oven and a 5-element electric cooktop featuring two 6 in.The cooktop features 5 sealed burners including specialty burners. Use the simmer burner to gently prepare delicate foods and.The cooktop features 5 sealed burners including specialty burners. Use the simmer burner to gently prepare delicate foods and.Freestanding Electric Smooth top Range with Self-Cleaning Oven lets you cook more at once, with a 5.3 cu. ft. capacity oven and a 5-element electric cooktop featuring two 6 in.Equipped with bright lighting to.It's equipped with bright lighting to keep.Featuring 4K Upscaler and Active HDR technology, this TV automatically improves resolution and picture quality in real time. This LG.ThinQ AI supports Alexa and Google Assistant for convenient voice control, while the wide viewing angle provides 100.Adjustable Temperature Control allows you to select the correct temperature for your needs. Additionally, stay organized.Euclid, OH 44132 Phone: 216-441-4500 Euclid, OH 44132. Up and Down arrows will open main level menus and toggle through sub tier links. Enter and space open menus and escape closes them as well. Tab will move on to the next part of the site rather than go through menu items. Download a digital copy of your owner's manual, use and care manual, installation information, and energy guides.You can save paper and ink by printing only the pages for the language you need. If you’re look for quick instructions or solve problems concerning your dehumidifier, please check our Troubleshooting page.

frigidaire refrigerator ice maker manual

Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly. Required Part Refrigerator Ice Maker Assembly Enter model number to search for the required part specific to your product Browse our parts categories to select from a variety of parts for your product SHOP PARTS Common Solution 04 - Icemaker Module The icemaker module is equipped with a motor that cycles the ice ejector arms or turns a tray to eject the cubes into the ice bucket. When the thermostat or sensor on the icemaker tray reaches about 15 degrees Fahrenheit, the motor cycles to release the ice cubes. At the end of the cycle, the icemaker module sends power to the water inlet valve to refill the tray with water. If the icemaker module is defective, the ice maker won’t make or dispense ice. If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades. There are usually test points in the module that a technician can use to further diagnose problems with the module.The water inlet valve supplies water to the ice and water dispenser. The water inlet valve requires a minimum of 20 psi to function properly. Check the water flow and test the pressure to determine if it is at least 20 psi. 06 - Door Switch The door switch turns off the ice and water dispenser when the refrigerator door is open. If the door switch fails, the dispenser will not turn on. To determine if the door switch is defective, use a multimeter to test it for continuity. If the door switch does not have continuity when activated, replace it.

• frigidaire refrigerator ice maker manual, frigidaire refrigerator ice maker troubleshooting, frigidaire gallery refrigerator ice maker troubleshooting, frigidaire professional refrigerator ice maker troubleshooting, frigidaire gallery fridge ice maker troubleshooting, frigidaire refrigerator ice maker not working troubleshooting, frigidaire refrigerator ice maker manual, frigidaire refrigerator ice maker manual, frigidaire refrigerator ice maker manual.

It can completely fill the Once ice maker begins Otherwise, the ice maker's To gain access to the ice Lift the wire signal This function terminates Turn the ice maker on. Before replacing. Hold times are long. Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Featured Video Top 6 Reasons Refrigerator Ice Maker Isn’t Working? 03:46 881,471 1,456 Common solutions for: Why is my Frigidaire refrigerator ice maker not working? 01 - Freezer Temperature is Above 10 Degrees F (-12C) If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed. 02 - Water Inlet Valve The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If t. he water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve.

The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Avoid connecting power to your refrigerator you must unplug the power cord from the electrical outlet. Shelves may break suddenly if nicked, scratched, or exposed to sudden Location Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug. If you do not hook up water to the refrigerator, remember to turn the ice maker off. Toe Grille Installation and Removal To install toe grille 1 Open both doors. Slide left and right sides of toe grille over lower hinges of refrigerator. 2 While pushing toe grille firmly against cabinet, fasten bottom clips of toe grille to cabinet. 3 Fasten top clips to cabinet. 4 Close the doors. Fasten right and left side clips into groove of bottom hinge. The compressor will not be able to maintain proper temperatures inside the refrigerator. Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator. Press firmly on top of toe grille until top of toe grille pops off. Pull toe grille outward toward your body and off of lower hinges. Removing Toe Grille If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be Your refrigerator should be positioned to allow easy access to a counter or table when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened. Guidelines for final positioning of your refrigerator: All four corners of the cabinet must rest firmly on the floor.

Required Part Refrigerator Door Switch Enter model number to search for the required part specific to your product Browse our parts categories to select from a variety of parts for your product SHOP PARTS Common Solution The Right Parts for the Job We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need. Page Count: 32 Remove all staples from the carton. Staples can cause severe cuts, and also destroy finishes if they come in contact with other appliances or furniture. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Child Safety Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.Operating the refrigerator with insufficient power can damage the compressor. CFClHCFC Disposal Pressing and holding the OnlOff button for Your old refrigerator may have a cooling system three seconds, located on the temperature that used CFCs or HCFCs (chlorofluorocarbons control panel (Electronic controls), or or hydrochlorofluorocarbons). Other refrigerants your refrigerator's cooling system, but does may also cause harm to the environment if not disconnect the power to the light bulb released to the atmosphere, and other electrical components. To turn off If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release refrigerant, you may be subject to fines and imprisonment under These guidelines must be followed to ensure that safety mechanisms in this refrigerator will operate properly.

Assembly Screws Non-Adjusting Hinge (some models) 6 Lay the door on its side to avoid damage to the water tube extending from the bottom hinge. To reinstall the freezer door, reverse the above steps. Be sure doors are set aside in a secure position where they cannot fall and cause personal injury. The rounded end of the handles may be sharp (some To ensure proper installation of handles, please review these instructions and illustrations thoroughly prior toinstalling the handles. 1 Remove handles from carton and any other protective packaging. Position freezer handle end caps over upper and lower pre-installed shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the refrigerator door. While holding handle firmly against door, fasten upper and lower Allen set screws (B) with supplied Allen wrench. Repeat steps 2 and 3 toinstall refrigerator handle. Ensure the holes for the set screws are facing towards the freezer door. All set screws should be tightened and sub-flush (Allen set screw should be seated just below the surface of the end cap) of handle end cap. The end caps should be drawn tight to freezer and refrigerator doors with no gaps:.Do not use a self-piercing type shutoff valve. Do not re-use compression fitting or use thread seal tape. A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve. Ensure that your water supply line connections comply with all local plumbing codes. Before Installing The Water Supply Line, You Will Need: e e e Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips TM screwdriver Access to a household cold water line with water pressure between 30 and 100 psi. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

The cabinet should be level at the front and rear. Doors should align with each other and be level. All of these conditions can be met by raising or lowering the adjustable front rollers. Raise To level the doors using the adjustable lower hinge (some models): Before leveling either door, remove set screw that locks door height into position. (The door cannot be adjusted without set screw removed). Reinstall set screw, locking the door height.Rear Cover Float cover Screw Screws Top I i Cover i I I I Hinge Screws Top,Hinge To remove the refrigerator doer: 1 Trace lightly around the door's top hinge with a pencil. This makes reinstallation easier. To prepare for removing the doors: 1 Make sure the electrical power cord is unplugged from the wall outlet. Open both doors and remove the toe grille (as explained in the Installation Instructions that came with your appliance). 3 Remove any food from the door shelves. Remove the two screws from the top hinge. Lift the door off of the bottom hinge and set it aside. Hinge Adjustable Hinge (some models) To reinstall the refrigerator door, reverse the above steps. To remove the freezer top hinge cover: i Remove the two screws from each cover over the top door hinges. 2 Lift hinge cover straight up and off. The connector releases when you press its outer sleeve inward. Remove the screws from the top hinge and pull the multi-wire cable through it. Lift the door off of the bottom hinge. Remove the two bottom hinge screws and hinge if necessary. To Disconnect 1: Press outer ring against face of fitting To Connect Insert tube and push until mark touches face of fitting Door, Water Assembly Screws Adjustable Hinge (some models) Hinge To remove the freezer door; 1 Detach the multi-wire cable connector located above the top hinge. Grasp both sides of the connector firmly and pull apart. 2 Trace lightly around the hinge with a pencil. This makes reinstallation easier. Hinge.

Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets. Cantilever Glass Shelf Cantilever Sliding Glass Shelf The dairy compartment, which is warmer than the general food storage section, is intended for short term storage of cheese, spreads, or butter. Fresh Drawers with Humidity Control (some models) The fresh drawers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. The fresh drawers feature humidity control which allows you to adjust the humidity within the drawer. This can extend the life of fresh vegetables that keep best in high humidity. Wash items in clear water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing. Crisper Humidity Control Leafy vegetables keep best when stored with the humidity control set on Higher Humidity, or in a drawer without a Humidity Control. This keeps incoming air to a minimum and maintains maximum moisture content. Crispers Crispers allow you the flexibility to store any manner of items including fruits, vegetables, nuts, etc. Crispers do not feature humidity controls. Crisper Drawer Door storage Door bins and shelves are provided for convenient storage of jars, bottles, and cans. Frequently used items can be quickly selected. Some models have door bins that can accommodate gallon-sized plastic drink containers and economy-sized jars and containers. Some bins are adjustable for maximum storage capacity. Cool Drawer (some models) Some models are equipped with a Cool Drawer for storage of luncheon meats, spreads, cheeses, and other deli items. This drawer does not have a separate temperature control. Chill Drawer temperatures can be adjusted by sliding the Chill Drawer Temperature Control in either direction. Use this pan for short term storage of bulk meat items.

If meats are to be kept longer than one or two days, they should be frozen. The Chill Drawer is fixed and cannot be moved up or down. If fruits or vegetables are to be stored in the Chill Drawer, set the Chill Drawer Temperature Control to a warmer setting to prevent freezing.This system needs to be completely filled with water when first connected to an external supply line. For proper dispenser operation, recommended water supply pressure should fall between 30 psi and 100 psi. Excessive pressure may cause water filter to malfunction.Keep the glass in this position until water comes out of the dispenser. How Huch Ice Will a Rear Hounted Ice Haker Produce in 24 Hours. A rear mounted ice maker will produce 3 to 4 pounds of ice every 24 hours, depending on usage conditions. Ice is produced at a rate of 8 cubes every 75 to 90 minutes. Using the Ice Maker after Installation Before making ice for the first time, be sure to prime the water supply system. Air in new plumbing lines can result in two or three empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. Your ice maker is shipped from the factory with the wire signal arm in the ON position (side mounted) or with the switch turned ON (rear mounted). If the ice maker is not turned off and the water supply is not connected, the water valve will.The water dispenser has a built-in device that shuts off the water flow after three minutes of continuous use. To reset this shutoff device, simply release the dispenser paddle. Ice Production: What to Expect How much ice will a side-mounted ice maker produce in 24 hours. A side mounted ice maker will produce 4 to 4.5 pounds of ice every 24 hours, depending on usage conditions. Ice is produced at a rate of 8 cubes every 75 to 90 minutes. The ice maker also has a built-in wire signal arm, which automatically stops ice production when the ice bin is full.

Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator.To Connect Water Supply Lime To Ice Maker Inlet Valve 1 2 3 4 Disconnect refrigerator from electric power source. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve. Remove plastic cap from water valve inlet and discard cap. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.Reconnect refrigerator to electrical power source.Increases the production of ice. Deactivates after 12 hours. A green indicator light will be illuminated above the active feature.A green indicator light will be illuminated above the active feature. Setting cooling temperatures mode OF oC water filter Toggles display from Fahrenheit to Celsius. Displays the current status of the water filter (Good, Order, or Replace).Press alarm reset to acknowledge the alarm. Other modes may be turned off until the alarm is acknowledged. When the power fail alert is acknowledged, the refrigerator will resume normal operation. The high temp alarm may also be illuminated until a safe operating range temperature has been reached. The alarm will reset after two minutes or when the ice cube is removed and the set key is pressed to reset. Sabbath Mode The Sabbath Mode is a feature that disables portions of the refrigerator and its controls in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community.

In the Sabbath Mode, the High Temp alarm is active for health reasons. If a high temperature alarm is activated during this time, for example due to a door left ajar, the alarm will sound intermittently for about two minutes. The alarm will then silence on its own and a red high temperature icon will display. The high temp icon will continue to display, even if the door is closed, until the Sabbath mode is exited and the icon reset. For further assistance, guidelines for proper usage and a complete list of models with the Sabbath feature, please visit the web at http:\\www.star-k.org. While in Sabbath Mode, neither the lights, dispenser, nor the control panel will work until Sabbath Mode deactivated Refrigerator stays in Sabbath Mode after power failure recovery. It must be deactivated with the buttons on the control Although you have entered the Sabbath Mode, the ice maker will complete the cycle it had already initiated. The ice cube compartment will remain cold and new ice cubes can be made with standard trays. Shelves may break suddenly ifnicked, scratched, or exposed tosudden temperature change. Allow the glass shelves to stabilize toroom temperature before cleaning. Do not wash in dishwasher. Cantilever Shelf Adjustment Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Cantilever shelves are supported at the back of the refrigerator. To adjust cantilever shelves: O Lift front edge up. O Pull shelf out. Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket. Lower the shelf into the desired slots and lock into position. SpillSafe TM glass shelves (some models) catch and hold accidental spills. In some models, the SpillSafe TM shelves slide out for easy access to food and for fast cleaning. The shelves slide out independently of their mounting brackets. Just pull the front of the shelf forward.

DO NOT use this signal arm to manually stop the ice maker.If you have a side mounted ice maker you may also experience hollow cubes partially frozen cubes with water inside. When these cubes are harvested, they break open and spill water over the other ice cubes in the ice container, forming a solid mass of ice. As the water filter nears the end of its useful life and becomes clogged with particles, less water is delivered to the ice maker during each cycle. The ice maker can't fill every cube in the ice maker mold, leading to small cubes or chips that can get caught between the ice ejector blades and the stripper. Remember, if your ice maker is jamming with small ice cubes or it's been six months or longer since you last changed your water filter replace the water filter with a new one. Poor quality household water may require the filter to be changed more frequently. Empty the ice container as explained below. Occasionally shake the ice container to keep ice separated. If your refrigerator is not connected to a water supply or the water supply is turned off, turn Off the ice maker., If you need a large quantity of ice at one time, it is best to get cubes directly from the ice container. The following sounds are normal when the ice maker is operating: Motor running Ice dropping into ice container Water valve opening or closing Ice loosening from tray Running water, When dispensing ice, you will hear a snapping or clicking sound when the ice chute opens and closes. To avoid splashing, dispense ice into your container before adding liquids. It is normal for ice to fill to the top of the ice bin. Turn Off the ice maker when cleaning the freezer and during vacations. If you turn Off the ice maker for a long period of time, you should also turn off the water supply valve. Chemicals from a malfunctioning water softener can damage the ice maker. If the water supply to your refrigerator is softened, be sure the softener is maintained to work properly.

To clean the ice maker: 1 Turn Off the ice maker. 2 3 4 5 Remove the ice bin by lifting up and out. Empty and carefully clean the ice bin with mild detergent. Rinse with clear water. Do not use harsh or abrasive cleaners. Allow the ice bin to dry completely before replacing in the freezer. Remove ice chips and clean the ice bin shelf and the freezer door chute. 6 Replace the ice bin. Turn On the ice maker to resume ice production. Remove and empty the ice storage bin if: An extended power failure (one hour or longer) causes ice cubes in the ice storage bin to melt and freeze together, jamming the dispenser mechanism. You do not use the ice dispenser frequently. Ice cubes will freeze together in the bin, jamming the dispenser mechanism. Remove the ice storage bin and shake to loosen the cubes or clean as explained above. Auc NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice storage bin and dispenser mechanism. When removing or replacing the ice bin, DO NOT rotate the auger in the ice bin. If the auger is accidentally rotated, you must realign the auger by turning it in 90 degree turns (see below) until the ice bin fits into place with the drive mechanism. If the auger is not properly aligned when replacing the ice bin, the refrigerator will only dispense Crushed Ice. The freezer door may also not close properly causing warm air to leak into the freezer.. The water filter system filters all dispensed drinking water, as well as the water used to produce ice. Air FHter (some models) The air filter is located at the top of the fresh food compartment next to the water filter. Replacing the Air Filter In general, you should change the air filter every six months (the filter status light on the control panel prompts you to replace the filter after six months) to ensure optimal filtering of refrigerator odors.

You may want to adjust this time period depending on the types and amounts of food you typically store in your refrigerator. To replace your PureSeurce Ultra TM air filter: 1 Pull the air filter housing straight out. 2 Remove the old filter and discard it. 3 Unpack the new filter and place it inside the housing. Water Filter The water filter is located at the top right side of the fresh food compartment. Replacing the Water Filter In general, you should change the water filter every six months to ensure the highest possible water quality. If your refrigerator has not been used for a period of time (during moving for example), change the filter before reinstalling the refrigerator. 4 Slide the housing back into position. Frigidaire recommends that you order extra filters when you first install your refrigerator, and that you replace your filters at least once every six months.Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. Slide the old water filter cartridge straight out of the housing and discard it. Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing. Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector). Press a drinking glass against the water dispenser while checking for any leaks at the filter housing. Any spurts and sputters that occur as the system purges air out of the dispenser system are normal. 8 9 After filling one glass of water, continue flushing the system for about four minutes. Turn On the ice maker.These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable.

Following is a list of major components in your refrigerator and the sounds they can cause: A Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound. B Evaporator fan You may hear air being forced through the refrigerator by the evaporator fan. C Defrost heater During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may OCCUr. D Automatic ice maker When ice has been produced, you will hear ice cubes falling into the ice bin. F Condenser fan You may hear air being forced through the condenser. G Compressor Modern, high-efficiency compressors run much faster than in the past. The compressor may have a high- pitched hum or pulsating sound. H Water valve Makes a buzzing sound each time it opens to fill the ice maker. I Drain pan (not removable) You may hear water dripping into the drain pan during the defrost cycle. J Condenser May create minimal sounds from forced air. K Motorized damper May produce a light humming during operation. L ke chute When dispensing ice, you will hear a snapping or clicking sound when the solenoid opens and closes the ice chute. Energy efficient foam in your refrigerator is During automatic defrost cycle, a red glow in the back wall vents of your freezer compartment is normal Wipe up any spills immediately and clean the freezer and fresh food compartments at least twice a year. Do not use abrasive cleaners such as window sprays, scouring cleansers, brushes, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels, metallic scouring pads, or other abrasive cleaning materials or strong alkaline solutions. Shifting it from side to side may damage flooring. Be careful not to move the refrigerator beyond the plumbing connections.

Do not touch refrigerated surfaces with wet or If you store or move your refrigerator in freezing temperatures, be sure to completely drain the water supply system. Failure to do so could result in water leaks when the refrigerator is put back into service. Contact a. Vacation and moving tips Short, Leave refrigerator operating during vacations of three weeks or less.Be sure to wring excess water out of sponge or cloth before cleaning around controls, light bulb or any electrical part. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer's instruction. Do not use household cleaners containing ammonia or bleach. Rinse well and wipe dry with a clean soft cloth. Press Here Firml Push Upward Until the Extension Snaps In Place ! Pull Down Always use Frigidaire parts for replacement. To replace LED Lights: 1 Unplug your refrigerator's power cord. 2 Remove lens cover. 3 Remove LED board. 4 Replace LED board and snap in place assuring the light is facing in toward the unit (inside fresh food). 5 Replace lens cover. LED lights are in series so if one is bad or unplugged, several lights may not light up.Some lights have covers that you will need to remove before replacing the bulbs. Always use bulbs that are designed for appliance lighting. To replace light bulbs: Wear gloves when replacing light bulbs to avoid getting cut, 1 Unplug your refrigerator's power cord. 2 Wear gloves as protection against possible broken glass. 3 Remove light cover, if necessary. 4 Unscrew and replace old bulb with an appliance bulb of the same type and wattage (normally 40 watts). 5 Replace light cover, if necessary. 6 Plug in the refrigerator's power cord. Lig located behind right rear of ice container For the freezer ice maker, lower the wire signal arm. I water pipe is clogged Remove valve. Ensure that valve s not or restricted by foreign I a self-pierdng saddle valve. Allow 24 hours for temperature to stabilize.